Check that the TV box is powered on and tuned to an authorized cable channel. Should not b... . The Gateway will walk you through setting up your WiFi network upon first time setup. .
Device off. If the modem flashes back to green then it means it has lost signal or power. We have had tech out multiple times.. look ok to them As the outage is only for 5 min, and you can NEVER access shaw support that quickly, they never see it when its broken.Anyone have any ideas (other than switching to Telus which I am currently looking into)My neighbor used to be a Shaw installer and offered some insight.The phone support people also have access but until I specifically asked, them they did not seem to look at it.As all the cable from the pole to my modem had been changed, I asked for someone to check (change) the connector at the pole.
The light will be a solid white colour when the modem is up and running. No light. White (flashing) Ready for WiFi setup. .
There are also factory reset and WPS buttons for resetting the modem and connecting devices via WPS. The remote won't power it on. Do the values make sense, relative to the date/time on your computer? If you are having Internet connectivity issues you may want to update your Internet modem. . Why does equipment from Shaw seem so LOUSY?? (Yes, the battery's in the remote are good) I've tried unplugging the box for a half hr and plugging it back in. . Your friend will show-up at noon (Daylight), but you will show-up one hour later (Standard time), and you probably will not "connect" with your friend. Blue (flashing--up to 2 minutes) WPS pairing mode Go to Solution. That fixed my problem. am on the phone to them now, am annoyed When the box is properly powered, it will have a light on the front. . My neighbor used to be a Shaw installer and offered some...
. It just contest to flash the green light.
Amber (solid) Booting up (first stage) Amber (flashing) Downstream registration.
You must be signed in to add attachments Just open a web browser and follow the step-by-step instructions.Yes, wireless 802.11ac Wave 2 MU-MIMO (modes A, G, N, and AC) I took them and connected it with my pc and it won’t proceed from flashing yellow lights. . I an looking for a resolution to this. This is a problem with the bluecurve modem, as the phone, also with Shaw, does not fail. How to configure modem settings; The Admin Tool allows you to change various settings on the modem, everything from WiFi passwords to parental controls, and more advanced settings. But after I switch to bridge mode, it starts blinking fast. I have had contact with support but they do not see an issue as it has not happened while on call to them
Quick question, we have a hddsr 600 that wont turn on. If your computer has the wrong date/time, your computer will not ask for a "renewal" of the lease until after the lease has expired, which results in a "disconnection".Compare to not updating your classic wrist-watch for the start of Daylight Saving Time, and then agreeing to meet a friend at noon at a cafe'. However, if I disable bridge mode, it blinks like normal.
Light does not change, stays white. I have had a few months now without any issues.Further, just happened again and when I did a "Test Connectivity" from the modem admin, I get..Look at the values for "Lease obtained" and "Lease expires". Find information on the BlueCurve Gateway including key features, available connections and hardware specifications.The BlueCurve Gateway has an updated design and comes equipped with the latest WiFi technology.The BlueCurve Gateway has a single light on the top to indicate the modem status. Is this a known issue with Shaw, I am having the same things happening, brief freezes, unstable internet connection and then completely restores itself after a minute or so. I even rest the modem of the factory settings. If the modem is reset, it will go through the following sequence of lights as it reboots:Available connections on the BlueCurve Gateway include two Ethernet ports for hardwired devices, and dual-band WiFi (2.4GHz and 5GHz). After I set BlueCurve Modem to bridge mode, I notice the network light on the modem blinking very fast event I have no so much traffic.
But, if your wrist-watch is, say, 5 minutes slow, you will show-up 5 minutes late, annoying your friend, but you will "connect".Should not be long as it has gone out 4 times in the last few hours.I have stated timing it, and it seems to go out for 5 to 10 minutes.Lease Obtained.
The top of the modem seems a bit on the warm side as well. I am SERIOUSLY ready to jump ship from Shaw due to all the equipment problems! Any ideas on what to do? This article will provide insight into Shaw's Internet modems. I have also noticed that the fan inside the Bluecurve modem does not speed up like it used to. Green (flashing) Upstream registration. First couple of months new blue curve modem worked fine.Recently I started getting connection lost for about 5 minutes... every few hours... every day.Shaw support says it looks fine to them. Also, ensure the coax cable connections from the wall outlet, splitter, and modem are tightly seated. It just flashes the green light on the front panel.